NanoPave Ghost 1 Gal

    NanoPave Ghost 1 Gal

    Product Code: 21993

    $35.95 / ea

    Not yet rated
    Please choose a color below
    Qty ea
    Product is Only Available for In-Store Purchasing
    Save your project list for later and share with others by creating an account or signing in.

    Features

    • Works above 40°F (5°C).
    • Will not discolor.
    • Rapid installation.

    Helps Resist

    • Corrosion from de-icing salt.
    • Ultraviolet ray effects.
    • Motor oil & grease stains.

    Product Specifications

    Coverage

    One gallon of GATOR HYBRID SEALER will cover 200 square feet if using one of theALLIANCE GATOR POLYMERIC SAND and approximately 100 square feet if using non polymeric sand. Coverage will vary depending on joint size, thickness and porosity of the surface of the pavers or the stones.


    NanoPave Application

    Natural Stone &Flagstone

    Install flagstone or other natural stone on a well compacted base rock, topped with a half inch of masonry sand for cushioning. For the joint material, we recommend using a 1/4” or 3/8” minus crushed stone (CS) with fines or decomposed granite (DG).

    1. Step 1
      1. Base rock should be well compacted.
      2. ˝" of masonry sand overlay to cushion stone bed.
      3. Place Flagstone & Joint material
    2. Step 2
      1. Apply a flood coat of NanoPave® liquid with a hand pump or low pressure sprayer (15-20 psi) at the recommended rates. For wider joints, concentrate the NanoPave® spray in the joints. Note, only apply NanoPave® when pavers and joints are dry, and surface is thoroughly cleaned.
    3. Step 3
        1. Use a squeegee to remove excess NanoPave® from the surface of the pavers. With the squeegee, push the sealer into the joints, be sure to cover the surfaces of the pavers evenly. Allow 24 hours before use.

    For a higher gloss or more enhanced finish apply a second coat of NanoPave® at 200 sf./ gallon


    Brick/Concrete Pavers

    The following installation process is for unsealed pavers. If you are installing a new paver surface, simply follow the beginning steps in the "Natural Stone Installation" process: Compact sub-base, lay 1/4" sand, and then place bricks/pavers.

    1. Step 1
      1. Apply a flood coat of sand on top of the entire paver surface. Use a vibratory plate compactor to compact all the sand into the joints tightly.
      2. Use a push broom to sweep all sand remaining on paver surfaces evenly into the paver joints.
      3. Using a leaf blower (on low power), blow off all loose sand on the surface of the paving surface.
    2. Step 2
      1. Apply a flood coat of NanoPave® liquid with a hand pump or low pressure sprayer (15-20 psi) at the recommended rates. Note, only apply NanoPave® when pavers and joints are dry, and surface is thoroughly cleaned.
    3. Step 3
      1. Use a squeegee to remove excess NanoPave® from the surface of the bricks/pavers. With the squeegee, push the sealer into the joints, be sure to cover the surfaces of the pavers evenly. Allow 24 hours before use.

    For a higher gloss or more enhanced finish apply a second coat of NanoPave® at 200 sf./ gallon


    Weather Tips

    Do not apply if rain is expected within 24 hours. Protect paving from rain, sprinklers, or additional moisture for 24 hrs. following application If inclement weather occurs, cease application and cover treated material.


    Coverage

    Below are recommended coverage rates for applyingNanoPave®. The actual coverage rates may vary by afew gallons per square foot. When using NanoPave®Hi-Gloss, apply additional coat(s) for a richer, moreenhanced aesthetic (only when first coat has dried).

    Joint WidthCoveragePaver Type
    1/8” to 1/4”90-100 sq ft/galBricks/Concrete
    1/4" to 1/2" 75-90 sq ft/gal Tumbled Pavers
    1/4" to 1/2" 60-70 sq ft/gal Natural Stone
    1/2"-3" 30-60 sq ft/gal Natural/Flagstone
    Customers Who Viewed This Product Also Viewed